The passing level of the test has been passed. Congratulations.
The result obtained indicates excellent knowledge of the technical characteristics of ceramic tiles. But still read articles on incorrectly answered questions.
You scored 4 out of 5 possible points.
Your result: 80%
Question 1
Adhesive mixtures must comply with the requirements of the GOST R 56387 standard and be manufactured according to technological documentation approved by the manufacturer. The main indicators of the quality of adhesive mixtures ready for use (freshly prepared) are ...
Your Answer Option Right? Result
Water holding capacity
1 Average density
0 Resistance to slippage
1 Humidity
0 Minimum Density
0 Maximum Density
0 Open time
-1
Material on this issue is presented in the GOST R 56387 .
Question 2
What requirements must be met for hardened solutions of adhesive mixtures?
Your Answer Option Right? Result
The transverse deformation of class S1 adhesives must be at least 2.5 mm, class S2 – at least 5 mm.
1 The strength of the adhesive joint after exposure to high temperatures must be no less than:
0.5 MPa for C1;
1 The strength of the adhesive joint after exposure to an air-dry environment for 28 days must be no less than:
0.5 MPa for C0;
1 The open time to achieve an adhesive joint strength of at least 0.5 MPa should be for adhesives of the following class:
C0 and F – when gluing tiles after 10 minutes;
1 The strength of the adhesive joint after cyclic freezing and thawing must be no less than:
0.5 MPa for C1;
1 The strength of the adhesive joint after exposure to an aqueous environment must be no less than:
0.5 MPa for C1;
1 The strength of the adhesive connection to the base of fast-hardening class F adhesives after exposure in an air-dry environment for 6 hours should be no more than 0.5 MPa
0
Material on this issue is presented in the GOST R 56387 .
Question 3
The terms with their corresponding definitions are listed below. Indicate those for which the match is correct.
Your Answer Option Right? Result
Holding time after preparation is the maximum period of time during which a freshly prepared mortar mixture (after additional mixing without adding water) retains its technological properties.
0 Sliding is the displacement under the influence of gravity of tiles or slabs laid on a layer of mortar mixture treated with a notched trowel applied to a vertical or inclined surface.
1 Open time - the maximum period of time after applying a layer of mortar mixture of a given adhesion strength to the base on the base, during which it is allowed to lay facing tiles on the applied mortar mixture.
1 A notched trowel is a toothed tool that allows you to create a layer of mortar mixture on the base in the form of grooves of the same thickness.
1 Pot life is the period of time after mixing the mortar mixture necessary to achieve readiness for installation.
0 Adhesion is the ability of a layer of mortar mixture treated with a notched trowel to wet the facing tile.
0
Material on this issue is set out in the GOST R 56387 .
Question 4
Adhesive mixtures must comply with the requirements of the GOST R 56387 standard and be manufactured according to technological documentation approved by the manufacturer. The main indicators of the quality of adhesive mixtures in a dry state are ...
Your Answer Option Right? Result
Color
0 Bulk density
0 Low dust generation
0 Content of grains of the largest coarseness
1 Largest aggregate grain size
1 Humidity
1
Material on this issue is presented in the GOST R 56387 .
Question 5
An example of a symbol for an adhesive mixture based on a cement binder, intended for interior and exterior work, meeting increased requirements, with increased resistance to slipping, increased open time and high elasticity.
Your Answer Option Right? Result
Dry construction adhesive mixture C2 TE S1, GOST R 56387
0 Dry construction adhesive mixture C1 FE S2, GOST R 56387
0 Dry construction adhesive mixture C1 TE S2, GOST R 56387
0 Dry construction adhesive mixture C2 TE S2, GOST R 56387
1 Dry construction adhesive mixture C1 TE S1, GOST R 56387
0 Dry construction adhesive mixture C2 FE S2, GOST R 56387
0
Material on this issue is presented in the GOST R 56387 .
